SKU: 55373929758

Foam Cannon Orifice for Snow Foam Lance and Foam Cannon

Sale price$81.00 Regular price$90.00
Save 10%

Pay in installments of $22.50 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 18 - Jul 23

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Foam Cannon Orifice for Snow Foam Lance and Foam CannonThis Foam Cannon Orifice is a Nozzle Screw Jet for foam cannons (foam lances). Before buying this item, make sure your foam lance is purchased from or branded as MJJC, as it might not work correctly on other branded foam lances. What is the pressure range for each orifice? 0. 9mm orifice: for 50 Ba 725 PSI ~ 90 Bar 1305 PSI pressure washer 1. 1mm orifice: for 90 Bar 1305 PSI~ 110 Bar 1595 PSI pressure washer 1. 25mm orifice: for 110 Bar 1595 PSI ~ 150

This Foam Cannon Orifice is a Nozzle Screw Jet for foam cannons (foam lances). Before buying this item, make sure your foam lance is purchased from or branded as MJJC, as it might not work correctly on other branded foam lances.

What is the pressure range for each orifice?

  • 0.9mm orifice: for 50 Ba /725 PSI ~ 90 Bar/1305 PSI pressure washer
  • 1.1mm orifice: for 90 Bar/1305 PSI~ 110 Bar/1595 PSI pressure washer
  • 1.25mm orifice: for 110 Bar/1595 PSI ~ 150 Bar/2175 PSI pressure washer
  • 1.35mm orifice: for 150 Bar/2175 PSI ~ 280 Bar/4061 PSI pressure washer
  • 1.65mm orifice: for 280 Bar/4061 PSI ~ 340 Bar/4931 PSI pressure washer

 

There are two sizes of nozzle screw jets, 1.25mm and 1.1mm. Initially, each MJJC foam lance comes equipped with a 1.25mm nozzle screw jet. You may need the 1.25mm orifice as a replacement if the previous one is not working properly. However, if your pressure washer is not producing enough pressure or its output flow rate is too low, you may need a 1.1mm nozzle screw jet on your snow foam lance to produce thicker foam to better wash your vehicle. For example, in the USA, as the electrical voltage is 110v, most electrical power washers are very compact and produce lower pressure. For those pressure washers, most machines need a 1.1mm nozzle screw to create thicker foam. If your foam lance (foam cannon) works fine with your pressure washer, then there is no reason to replace the nozzle screw.

A 1.1mm orifice is recommended for most under 110Bar pressure washers. If your pressure washer produces over 110Bar, or the outflow rate is stronger than a normal 100Bar pressure washer after you put the 1.1mm orifice on your foam cannon, your pressure washer will probably pulsate. In that case, you can replace the 1.1mm orifice with the 1.25mm orifice, and it should operate as normal.

Frequently Asked Questions:

1. Why do the 1.1mm and 1.25mm nozzles look the same?

The 1.1mm and 1.25mm nozzles look exactly the same, except for the size of the holes—1.1mm and 1.25mm. The openings are very small, so the size difference can be difficult to notice with the naked eye.

2. Why doesn’t my foam lance (foam cannon) create thicker foam as others do?

The foaming performance depends on not only the foam lance but also the pressure and output rate of your power washer, as well as your car wash shampoo (soap). A foam lance will produce thicker foam with concentrated shampoo (soap), but most brands of shampoo (soap) are not concentrated, even from some of the best-selling brands.

3. Does this spare nozzle screw work with other brands of foam lances (foam cannons)?

No, this nozzle screw is specially designed for MJJC foam lances only.

4. Does the MJJC Foam Cannon come with an extra 1.1mm orifice?

Yes, every MJJC foam cannon comes with one extra, free 1.1mm orifice as a spare. The original orifice installed on the foam cannon measures 1.25mm.




Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 55373929758

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.4 ★★★★★
Based on 20 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
R
Verified Purchase
ralversity
Lake Worth, US
★★★★★ 3
Does the job, but assembling by yourself is a nightmare
Size: 4 Panel-88'', Color: Black
Does it do the job? Yes, although as others said there are small gaps but it's not a huge deal. The price is also good. But the reason I'm giving it a 3/5 is simply because the assembly for this was a complete nightmare. I honestly don't think I would recommend this to anyone unless they have another person to help them assemble it, because doing it by myself was terrible. I don't think I'd buy this again, I think I'd opt to just spend a bit more money and save myself the trouble personally.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 29, 2026
T
Verified Purchase
Talagand
Natrona Heights, US
★★★★★ 4
Reasonably adequate room divider
Size: 4 Panel-88'', Color: Beige
I'm reviewing this as I assemble it. Couple things: 1. I didn't expect as much assembly. I've ordered dividers before and they more-or-less came as one unit. Sometimes the panels needed screwing together. These require complete assembly and come largely as three rods: two make up vertical columns and snap together. Another one (called part "C") makes the horizontal columns and you have two of these per panel (one attaches to part "A" and the other part "B"). These parts are metal with a plastic shim. Using the wood screws to attach to part "C" is a real pain in the neck. There's not much holding the panel in place so it's a little tricky. One tactic I've found while I'm assembling that works for the initial connections from parts A and B to their respective "C" rods is to hold the screw in place with a screw driver and then rotating the rod around the screw. This will do a number on your hands if you aren't wearing gloves. This obviously doesn't work when completing the connection. Using a driller driver on this is really near impossible because there isn't anything you can use to secure it in place. You can use it on the first panel, but as it gets longer, it becomes increasingly difficult and because it isn't wood, it's really tight. I considered drilling larger pilot holes but since there are only 4x4=16 screws I need to screw in, I just decided to use my screw driver to complete it. 2. Also related to assembly. When completing the panels (attaching parts "A" and "B" to parts "C" that have the cloth cover on it), you have to be careful that when you tighten that side that it isn't loosening the other side. Because the pilot holes are so tight, you can end up rotating the rod, which rotates it in the same direction as looser on the original side. Having someone hold the "C" rod in place while you screw it in is probably the easiest approach. I didn't have a 2nd person, so I just had to keep flipping back and forth and tightening both sides as I screwed it in. Not the worlds biggest deal, but annoying nonetheless. 3. The way the instructions are written, they seem to suggest building this thing progressively; that is, you do panel 1, then 2, connect them together, then do 3 and connect it, etc. I took a different route that I suspect saved me quite a bit of trouble, and I assembled all four panels first and THEN connected everything together. 4. For the love of God make sure you check that the plastic tip is on the same side for every panel. Otherwise, you have to take one side apart again and reverse it. On the bright side, if this happens, you've essentially bored out the pilot holes to be the correct size... which is having me question if I shouldn't have just bored them out to the appropriate width in the first place. 5. Attaching all of the panels together is also an enormous pain in the ass unless you happen to have an 88" long elevated surface. Attaching the legs either requires you to elevate one side, which will invariably twist the inexplicably cheap material in the bottom connectors... or you can attach them sideways... or you can put this thing upright, having two people hold the panels in place while you use the allen wrench to tighten the bolts on the underside. None of those are particularly great options. NOW on to the utility itself. 1. The panels do let some light through (I didn't believe their advertising, and that was one of the reasons that I bought beige, is that I wanted it to not be too dark). They aren't transparent though, so it isn't that far off from their description. They functionally work great, and keep the mess of wires hidden and when I'm sitting at my desk, actually reflect quite a bit of light into my office. Great! 2. My wife has described these as "the most hideous piece of furniture ever conceived of by man." So it does not have spouse approval factor. Granted, she will seldom be in my office area, so that isn't the end of the world. 3. These are really hard to align in a way that doesn't look a little tacky. There are some plastic connectors but they don't do a bang up job of keeping these in place. Each panel is slightly tilted and it's... quite obvious. I may at some point make my own improvements to these to help make them more level. It's not a particularly expensive product so I wasn't expecting much so it's fine and I'm not going to ding them on the rating because of it. All said, would I buy this product again? Probably not. It's assembly was ~90 minutes which is about 75 minutes longer than I was anticipating spending on this (not including the 5 minute writeup that I'm doing here). But am I going to return it? Also no, if for no other reason I'd be just as annoyed taking it apart and putting it in the original box to return it.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 31, 2023
E
Verified Purchase
884EVER
Los Angeles, US
★★★★★ 5
Great privacy screen
Size: 4 Panel-88"W, Color: Grey
Nice item, easy to assemble.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 15, 2026
C
Verified Purchase
cara
Bozeman, US
★★★★★ 5
Great privacy screen
Size: 6 Panel-119"W, Color: Beige
I have a studio apartment and the bathroom is in my bedroom. I bought this to section the area off so guests can use my bathroom without seeing my entire bedroom. This is perfect for that! It looks very nice and offers alot of privacy. The screen is fabric and good quality! I’m a middle aged woman and put it together myself in about 2 hours. Love this!!!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 27, 2025
M
Verified Purchase
michael cornwell
Birmingham, US
★★★★★ 4
Nice divider 6 panel with wheels.
Size: 6 Panel-119"W, Color: Black, Size: 6 Panel-119"W, Color: Black
The wall works great , and I put it together by myself. I only gave it what I did because I have to move one or two of the panels on one end around a bit daily to make an opening to pass through. I find I have to check the screws that hold those legs/feet on frequently and retighten them. Beyond that everything was pretty good quality. (I ended up magnetizing an Allen wrench to one of the feet.) I also put on motion lights to the rollers so you’ll see them and don’t trip.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 19, 2026

recommand products